 |
This is the
rigid brake hose that screws into your left side and right
side Brembo F08 brake caliper on a 900SS but also works on
all bevel drives - assuming of course the caliper is in
front of the fork as per original. These are new old stock
BREMBO parts in perfect condition. |
 |
SS Line - M/C
to Splitter - 9"
Stainless steel brake line
that goes between the master cylinder and the stock splitter
under the lower triple clamp. This is a 9" long line that is
perfect for any bevel drive with clipons such as 750 Sport
or 900 Super Sport - available with a black cover as shown
or a silver cover. Kit includes 2 banjos and 4 crush
washers. |
 |
SS Line - M/C
to Splitter - 13"
Stainless steel brake line
that goes between the master cylinder and the stock splitter
under the lower triple clamp. This is a 13" long line that
is perfect for any bevel drive with euro style bars such as
750/860 GT or SD Darmah or raised clipons as found on SSD
Darmah - available with a black cover as shown or a silver
cover. Kit includes 2 banjos and 4 crush washers. |
 |
SS Lines -
Splitter to Caliper
This stainless steel
brakeline kit goes between the splitter and calipers - for
those of you who don't want to use [or don't have] the
original rigid line that goes between the caliper and hose.
I designed the lines to work on bevel drives with the brembo
F08 calipers mounted in front of OR behind the forks. The
kit is made for us by GALFER USA so you can assured of the
quality and it consists of what you see here: 2 ea 19"
lines, 2 banjo bolts and 6 crush washers. You can choose
either black [shown] or clear plastic hose also. Make sure
you choose the right splitter to master cylinder line
[available seperately] for your specific application to
finish off the deal. |
 |
SS Lines -
Splitter to Tube
This stainless steel
brakeline kit goes between the splitter and the rigid tube
threaded into the calipers - for those of you who want to
use the original rigid line that goes between the caliper
and hose. I designed the lines to work on bevel drives with
the brembo F08 calipers with rigid tubes mounted in front of
the forks. The kit is made for us by GALFER USA so you can
assured of the quality and it consists of what you see here:
2 ea 14.5" lines, 2 banjo bolts and 6 crush washers. You can
choose either black [shown] or clear plastic hose also. Make
sure you choose the right splitter to master cylinder line
[available seperately] for your specific application to
finish off the deal. |
Front SS brake line kit
for 750 GT |
This stainless
steel braided brake line kit is for a stock 750 or 860 GT single
line front F08 Brembo brake setup. Made by GALFER.
Replaces #0795.54.166/164
|
Front SS brake line kit
for 750 GT |
This stainless
steel braided brake line kit for 750 GT or 860 GT [with
single F08] is different than the one above as it goes
directly from the stock master cylinder to the caliper -
you remove the stock metal tube. 36" long overall. Made by GALFER.
Replaces #0795.54.166/164
and the metal tube
|
Front SS brake line kit
for Darmah |
This stainless
steel braided brake line kit is for a stock Darmah dual line front F08 Brembo brake
setup which utilizes a metal tube at each caliper.
Also fits 860GT, etc. Made by
GALFER.
Replaces - 1 ea
#824.54.160 and 2 ea #796.54.178
|
Rear SS brake line kit
for Darmah |
This stainless
steel braided brake line kit is for a stock Darmah dual line
rear F08 Brembo brake setup [master cylinder to splitter
to caliper]. Made by GALFER.
Replaces - 1 ea
#797.41.430 and 1 ea #801.41.425
|
Front SS brake line kit
for 900SS |
This stainless
steel braided brake line kit is for a stock Darmah dual line front F08 Brembo brake
setup which utilizes a metal tube at each caliper.
Also fits 860GT, etc. Made by GALFER.
Replaces - 1 ea
#0796.54.188 and 2 ea #796.54.178
|
Rear SS brake line kit
for 900SS |
This stainless
steel braided brake line kit is for a stock 900SS single line
rear F08 Brembo brake setup [master cylinder to caliper]. Made by
GALFER. It can be used on other models as well.
Replaces - 1 ea
#797.41.438
|
